NT850 LanScaperPRO kit with 2-8 remote
 
 
The NT850 LanScaperPRO™ Cabling and Network Tester combines the functions of a high-end cable tester and length measurement device with the capability to identify, monitor, and correct LAN issues associated with physical layer and link conditions in the network. In network mode testing, the easy-to-use NT850 LanScaperPRO enables quick identification at unknown RJ45 jacks for active Ethernet, POTS, token ring, or other devices as well as for presence of devices using power over Ethernet (PoE) at the other end of the jack or cable being tested. The NT850 LanScaperPRO pings network devices to verify connections and IP addresses, automatically accessing DHCP hosts to obtain network information and can quickly identify hubs, NICs, or auto MDI/MDI-X devices. It also conducts link tests to identify speed and capabilities of network drops. For cable testing, the NT850 LanScaperPRO provides full cabling testing, displaying wire map, ID, and any faults, including shorts, opens, miswires, split pairs, and reverses. The full-featured NT850 LanScaperPRO measures cable length and generates tone levels for signal tracing and cable identification on all pairs, a selected pair, or a selected pin.
 
Features
 
l

Identifies and measures power delivered by IEEE 802.3af PoE and legacy Cisco In-Line Power
l

Detects and reports speed and capabilities for active Ethernet and other devices up to 1 Gbps
l

Simultaneously pings three addresses at once to verify connectivity to network devices
l

Blinks a link indicator to identify hub or switch port and links to Cisco bridge or router ports using Cisco Discovery Protocol
l

Tests cabling configuration and verifies connectivity while conducting tests for opens, shorts, miswires, split pairs, and reverses
l

Displays length measurement for each pair in feet or meters
l

Generates selectable tones on selected pins for use with tone tracers
l Back-lit alphanumeric LCD with icon flags
l Applications:
 - Network testing for port discovery, ping test, and hub flash
 - Test PoE to ensure adequate power for powered devices such as VoIP phones
 - Identify speed up to 1 Gbps, duplex mode, wiring mode, and polarity of transmit pair on active Ethernet devices
 - Conduct single ended and remote cable tests with display of PASS, wiremap, ID, and faults for network cable
 - Measure cable length
 - Tone and trace cables
 - Wiremap network connections with remote identifiers
NT850 Package Contents:
1 TP40 12” Cable Ass RJ45 alligator clip
2 TP55 12” Cable Ass shielded, RJ45
2 TP20 7.5in. Cable Assembly with Two No-Fault RJ12 Connectors
1 TT100 High Sensitivity Tone Tracer
1 Nylon case
NT850 Accessories:
l TP40: 12in. Cable Assembly, RJ45/alligator clips
l TP55 12” Cable Ass shielded, RJ45
l TP20 - 7.5" no-fault RJ12 connectors for RJ11 or RJ45 jacks
l TT100 High Sensitivity Tone Tracer
l TP312: Set of 20 (1-20) RJ45 Wiremappers
l TP314: Set of 20 (1-20) RJ11 Wiremappers
l TP315: Set of 20 (1-20) Speaker Remotes
l TP609: 1 replacement remote TP600
l Set of 8 wiremap remotes, TP610
Specifications
Size (h x w x d): 4.5 x 8.87 x 18.56 cm
(1.77 x 3.49 x 7.31 in)
Weight (with batteries): 397 gm (14 oz)
Operating temperature: 0 to 50°C (32 to 122°F)
Storage temperature: –30 to 80°C (–20 to 176°F )
Battery life: 4 AA alkaline batteries

Times are for full-capacity batteries used continuously in one of the following modes:

 Standby -2 yrs
  Cable testing - 70 hrs (no backlight)
                    - 50 hrs (50% backlight)
  Network testing - 7 hrs (no backlight)
                       - 6.5 hrs (50% backlight)
Cable types:

Network/Ethernet cable, including CAT6, CAT5E, and CAT5
Min cable length for testing split pairs: 1 m (3 ft)
Min cable length for single-ended cable test:

1.25 m (4 ft)
Length measurement range (CAT5/6): 0 to 457 m (0 to 1,500 ft)
Qualified: CE, RoHS and WEEE